Child pages
  • Registering and de-registering DECT accessory devices


Contents

This page is documenting ways to register and deregister accessory dect devices.




De-registering

Base station available and working

A170 base station

  1. Press and hold "PAIR" button for about 10s
    1. Mute LED on base will light up red after 5s, keep holding button
  2. Release the button and press it again within 1s
  3. Headset should sound a beep and main LED should alternate RED/GREEN now

A230 DECT Dongle or A150 Dongle

  1. Press and hold corner button for about 10s
    1. Button LED on base will blink slowly RED 4s, keep holding button until flashing quickly
  2. Release the button and press it again within 1s
  3. All registered devices are now unregistered and the dongle should have the button LED lit up RED.

Base station unavailable

A170 or A150 Headset

Press the following buttons in direct sequence:

  • VOL UP >  PHONE ON  > VOL DN > PHONE ON > VOL UP > VOL DN > PHONE ON

PHONE ON means the button to pick up or end calls on the side of the headset.

If successfull the headset will sound a beep and status LED will alternate RED/GREEN.

C52-SP

  1. Press the "registration" button on the bottom of the device for 10s
  2. Release the button and press it again within 1s

If successfull the LED on the top of the device will show the sequence

  • RED → OFF → YELLOW → OFF

After this they blink regularly in yellow.



Registering

A170 base station

Note: only one headset can be registered at a time
  1. Make sure the A170 headset to be registered is not registered anywhere (LED alternating slowly RED/GREEN)
  2. Press and hold "Pair" button for about 5s
    1. Mute LED comes on RED
  3. Release button
  4. Within 10s place headset into charging cradle
    1. LED will start alternating quickly

If successfull "Mute" LED will turn off and headset LED will light steady.

A150 dongle

Note: only one headset can be registered at a time
  1. Make sure the A150 headset to be registered is not registered anywhere (LED alternating slowly RED/GREEN)
  2. Press and hold corner button for about 4s
    1. Button LED blinks slowly RED
  3. Release button
  4. Within 10s place headset into charging cradle
    1. LED will start alternating quickly

If successfull corner LED will turn off and headset LED will light steady.

A230 DECT dongle

Note: one headset and one C52-SP can be registered at a time
Registering a headset
  1. Make sure the headset to be registered is not registered anywhere (LED alternating slowly RED/GREEN)
  2. Press and hold corner button for about 4s
    1. Button LED blinks slowly RED
  3. Release button
  4. Within 10s place headset into charging cradle
    1. LED will start alternating quickly

If successfull corner LED will turn off and headset LED will light steady.

Registering a C52-SP
  1. Make sure the C52-SP to be registered is not registered anywhere (LED alternating slowly RED/GREEN)
  2. Press and hold corner button for about 4s
    1. Button LED blinks slowly RED
  3. Release button
  4. Press and hold C52-SP "registration" button for about 5s
    1. LEDs will start alternating RED/GREEN

If successful, corner LED will turn off and C52-SP will sound two beeps.



Using A170 and C52 simultaneously

It is possible to use the A170 and C52 simultaneously while connected to the A230. Once you have registered both devices, you can change the audio device in the following way:

-If the audio is currently running over the A170 and you would like to take over the audio on the C52, press the middle button on the C52:


-If the audio is currently running over the C52 and you would like to take over the audio on the A170, press the side call button on the A170:




Related articles: