D765 No webpage, but network works

Hello, 
I have a Snom D765 that have FW original from Vodafone, I flash it with snomD765-10.1.64.14-SIP-r.bin in rescue mode, and reset all settings.
The phone stats and I can ping it, but no webpage as available, the option in settings was enable, but no http/https port is open.
I connect to serial port at 115200 to see the debug, but in my opinion they never stats the webserver:

_{BRCM boot1.
STICKYBITS=0x00000280
STRAPS=0x3c000440
NAND: ID: 0xef 0xf1 
(B)}

_{Found valid partition table at 0x00000000
(C)
(D)
magic 0x0000babe
size  0x00070c08
Checksum PASSED: 0x027cef59
Jump 0x00004010}

_{U-Boot 2010.12-00001-gd311851f1 (Feb 25 2019 - 14:19:16)}

_{DRAM:  126 MiB
NAND:  Hamming, 128 MiB
MMC:   
Found Environment offset in OOB..
In:    serial
Out:   serial
Err:   serial
Net:   Broadcom BCM111XX Ethernet driver 0.1
bcm11107_eth-0
MAC: 00:04:13:94:3c:44}

_{Hit any key to stop autoboot:  0} 

_{NAND read: device 0 offset 0xec0000, size 0x400000
 4194304 bytes read: OK
## Booting kernel from Legacy Image at 00400000 ...
   Image Name:   Linux-2.6.27.47
   Image Type:   ARM Linux Kernel Image (uncompressed)
   Data Size:    1938212 Bytes = 1.8 MiB
   Load Address: 0d000000
   Entry Point:  0d000000
   Verifying Checksum ... OK
   Loading Kernel Image ... OK
OK
Using machid 0x922 from environment}

_{Starting kernel ...}

_{Uncompressing Linux to 0x00208000.................................................................................................................................. done, booting the kernel.
Linux version 2.6.27.47 (stephentao@stephentao-VirtualBox) (gcc version 4.3.2 (Wind River Linux Sourcery G++ 4.3a-291) ) #21 PREEMPT Tue May 12 14:42:44 HKT 2020
CPU: ARMv6-compatible processor [410fb767] revision 7 (ARMv7), cr=00c5387f
Machine: snomD765
Memory policy: ECC disabled, Data cache writeback
CPU0: D VIPT write-back cache
CPU0: I cache: 32768 bytes, associativity 4, 32 byte lines, 256 sets
CPU0: D cache: 32768 bytes, associativity 4, 32 byte lines, 256 sets
Built 1 zonelists in Zone order, mobility grouping on.  Total pages: 32004
Kernel command line: console=ttyAMA0,115200n8 root=/dev/mtdblock7 rw rootfstype=jffs2 noinitrd ethaddr=00:04:13:94:3C:44 fwenv=/dev/mtd2,0x0,0x20000,0x20000,4 bootmemheap=1M mtdparts=bcm_umi-nand:0x000a0000(bootloader),0x000e0000(uboot),0x00080000(ubootenv),0x00400000(rescuekernel),0x00800000(rescuefs),0x000c0000(data),0x00400000(kernel),0x06d40000(rootfs)
switch_ethaddr_setup: mac address  0- 4-13-94-3c-44 
BCMRING_BASE_bootmemheap_calc_fb_mem: Reserving memory for frame buffer w:320 h:240 bpp:2 x 2 (614400 bytes)
LcdHeapSize: framebuffer rounded up to page size = 614400 = 0x96000 bytes
VdecHeapSize: vdec heapsize = 0x0 bytes
mmDmaHeapSize: mmdma heap size = 0 = 0x0 bytes
bootmemheap_setup: total heapsize = 0x96000 bytes = 150 pages
bootmemheap_setup: Allocated 150 pages at 0xc0532000.
PID hash table entries: 512 (order: 9, 2048 bytes)
bcmring_init_timer
SVN Revision: UNKNOWN
Console: colour dummy device 80x30
Dentry cache hash table entries: 16384 (order: 4, 65536 bytes)
Inode-cache hash table entries: 8192 (order: 3, 32768 bytes)
Memory: 126MB = 126MB total
Memory: 122864KB available (3748K code, 371K data, 104K init)
Calibrating delay loop... 498.07 BogoMIPS (lpj=2490368)
Mount-cache hash table entries: 512
CPU: Testing write buffer coherency: ok
net_namespace: 780 bytes
NET: Registered protocol family 16
bcmring_ddrvpmphase_init: *** DDR Phase Value: 0x1f
Chip: 0x00011198
gpio_init called
GPIO Control Driver: 1.00 (built on May 12 2020 14:41:31)
knllog_init
perfcnt_init
calling host_cpu_usage_init
*************Starting host ICP thread **************   
SCSI subsystem initialized
usbcore: registered new interface driver usbfs
usbcore: registered new interface driver hub
usbcore: registered new device driver usb
SPU: driver probed. tx_ring virt=0x08ff000000 phys=0x087e54000
Bluetooth: Core ver 2.13
NET: Registered protocol family 31
Bluetooth: HCI device and connection manager initialized
Bluetooth: HCI socket layer initialized
NET: Registered protocol family 2
IP route cache hash table entries: 1024 (order: 0, 4096 bytes)
TCP established hash table entries: 4096 (order: 3, 32768 bytes)
TCP bind hash table entries: 4096 (order: 2, 16384 bytes)
TCP: Hash tables configured (established 4096 bind 4096)
TCP reno registered
NET: Registered protocol family 1
bcmring_pm_init: Initializing Power Management for BCMRING....
JFFS2 version 2.2. (NAND) (SUMMARY)  © 2001-2006 Red Hat, Inc.
msgmni has been set to 240
pka_init
io scheduler noop registered (default)
LCDFB-Backlight: 0.1
Broadcom RNG Driver
RNG: Driver initialized
MMDMA: Using dedicated DMA channel
MMDMA: No memory allocation is allowed!
MMDMA: Module initialized
MMDMA: No memory allocation is allowed!
MMDMA: Module initialized
GE: Driver initialized
bootmemheap_alloc: 'bcmring_lcd' allocated 0x96000 bytes at 0xc0532000
LCD: Driver initialized
LCD: name=Powertip ph320240t 320 x 240 width=320 height=240 bytes/pixel=4
[RZ]Eth Status Get module start 
 Call bcmring_eth_led register cdev 
 Call bcmring_eth_led major = 198 
[RZ]Request GPIO group 
HPM Driver: 1.00 (built on May 12 2020 14:42:02)}

_{KNLLOGDRV: Driver initialized
HAL Audio Driver: 1.0
HAL Audio platform support installed. Built May 12 2020 14:42:03
Audio Mixer Driver: 1.0
Broadcom GPIO Driver: 1.00
BSC: Driver initialized
Serial: AMBA PL011 UART driver
UARTA: ttyAMA0 at MMIO 0x80012000 (irq = 46) is a AMBA/PL011
console [ttyAMA0] enabled
UARTB: ttyAMA1 at MMIO 0x80013000 (irq = 44) is a AMBA/PL011
------->bcmring_net_init(): <6><6>Broadcom BCMRING network driver 0.2.0}

_{------->bcmring_net_init(): <6>bcmring_net => RL: Packet based rate limit enable = 0
------->bcmring_net_probe(): <6>bcmring_net configuration: brcmMode=0, descRx=64, descTx=1024
------->ethStart(): <4>Ethernet initialization successful (rc=0)
SLIP: version 0.8.4-NET3.019-NEWTTY (dynamic channels, max=256).
CSLIP: code copyright 1989 Regents of the University of California.
tun: Universal TUN/TAP device driver, 1.6
tun: (C) 1999-2004 Max Krasnyansky <maxk@qualcomm.com>
Driver 'sd' needs updating - please use bus_type methods
BCM UMI MTD NAND Driver: 1.00
NAND device: Manufacturer ID: 0xef, Chip ID: 0xf1 (Unknown NAND 128MiB 3,3V 8-bit)
Scanning device for bad blocks
8 cmdlinepart partitions found on MTD device bcm_umi-nand
Creating 8 MTD partitions on "bcm_umi-nand":
0x00000000-0x000a0000 : "bootloader"
0x000a0000-0x00180000 : "uboot"
0x00180000-0x00200000 : "ubootenv"
0x00200000-0x00600000 : "rescuekernel"
0x00600000-0x00e00000 : "rescuefs"
0x00e00000-0x00ec0000 : "data"
0x00ec0000-0x012c0000 : "kernel"
0x012c0000-0x08000000 : "rootfs"
gpiomux_requestGroup: group=17 pin=39 ggpiomux_rc_CONFLICT - gInit.is_requested && (gInit.is_requested(pin) != NULL) 'display'
usbcore: registered new interface driver cdc_acm
cdc_acm: v0.26:USB Abstract Control Model driver for USB modems and ISDN adapters
Initializing USB Mass Storage driver...
usbcore: registered new interface driver usb-storage
USB Mass Storage support registered.
usbcore: registered new interface driver usbserial
usbserial: USB Serial support registered for generic
usbcore: registered new interface driver usbserial_generic
usbserial: USB Serial Driver core
BCMRING Keypad Input Driver: 1.00
input: keypad as /devices/virtual/input/input0
Keypad: rows=9 cols=9 scancode=81 Debounce count=200 Sampling freq=9002
BCMRING RTC, (c) 2009 Broadcom Corporation
Software Watchdog Timer: 0.07 initialized. soft_noboot=0 soft_margin=60 sec (nowayout= 0)
Bluetooth: Generic Bluetooth USB driver ver 0.3
usbcore: registered new interface driver btusb
usbcore: registered new interface driver hiddev
usbcore: registered new interface driver usbhid
usbhid: v2.6:USB HID core driver
nf_conntrack version 0.5.0 (2048 buckets, 8192 max)
ip_tables: (C) 2000-2006 Netfilter Core Team
ClusterIP Version 0.8 loaded successfully
arp_tables: (C) 2002 David S. Miller
TCP cubic registered
NET: Registered protocol family 10
lo: Disabled Privacy Extensions
IPv6 over IPv4 tunneling driver
sit0: Disabled Privacy Extensions
NET: Registered protocol family 17
Bridge firewalling registered
Ebtables v2.0 registered
Bluetooth: L2CAP ver 2.11
Bluetooth: L2CAP socket layer initialized
Bluetooth: SCO (Voice Link) ver 0.6
Bluetooth: SCO socket layer initialized
Bluetooth: RFCOMM socket layer initialized
Bluetooth: RFCOMM TTY layer initialized
Bluetooth: RFCOMM ver 1.10
Bluetooth: BNEP (Ethernet Emulation) ver 1.3
Bluetooth: BNEP filters: protocol multicast
Bluetooth: HIDP (Human Interface Emulation) ver 1.2
RPC: Registered udp transport module.
RPC: Registered tcp transport module.
802.1Q VLAN Support v1.8 Ben Greear <greearb@candelatech.com>
All bugs added by David S. Miller <davem@redhat.com>
loading module:drivers/leds/leds-snom7xx.c build @14:42:05
initializing drivers/leds/leds-snom7xx.c
Empty flash at 0x0281d970 ends at 0x0281e000
VFS: Mounted root (jffs2 filesystem).
Freeing init memory: 104K
init started: BusyBox v1.31.1 (2020-04-24 17:02:26 CEST)
starting pid 442, tty '': '/etc/init.d/rcS'
--- System snomD765 is starting up ---
--- Mounting File System ---
JFFS2 notice: (441) check_node_data: wrong data CRC in data node at 0x0281cf34: read 0x84048469, calculated 0x1644d1d9.
--- Using SHA256 client certificate ---
--- Setting up network ---
--- Starting up daemons ---
Start rngd
--- Loading snomD765 modules ---
bcmring_eth_sla: module license 'Proprietary' taints kernel.
Load USB EHCI kernel module
GPIO-19 autorequested
USB: Port 1 has been brought up as Host
bcm-ehci: init device 1
bcm-ehci bcm-ehci.1: bcm-ehci
bcm-ehci bcm-ehci.1: new USB bus registered, assigned bus number 1
bcm-ehci bcm-ehci.1: irq 17, io mem 0xf8410800
bcm-ehci bcm-ehci.1: USB 2.0 started, EHCI 1.00, driver 10 Dec 2004
usb usb1: configuration #1 chosen from 1 choice
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 1 port detected
usb usb1: New USB device found, idVendor=1d6b, idProduct=0002
usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1
usb usb1: Product: bcm-ehci
usb usb1: Manufacturer: Linux 2.6.27.47 ehci_hcd
usb usb1: SerialNumber: bcm-ehci
bcm-ohci: init device 1
bcm-ohci bcm-ohci.1: bcm-ohci
bcm-ohci bcm-ohci.1: new USB bus registered, assigned bus number 2
bcm-ohci bcm-ohci.1: irq 17, io mem 0xf8410000
usb usb2: configuration #1 chosen from 1 choice
hub 2-0:1.0: USB hub found
hub 2-0:1.0: 1 port detected
usb usb2: New USB device found, idVendor=1d6b, idProduct=0001
usb usb2: New USB device strings: Mfr=3, Product=2, SerialNumber=1
usb usb2: Product: bcm-ohci
usb usb2: Manufacturer: Linux 2.6.27.47 ohci_hcd
usb usb2: SerialNumber: bcm-ohci
HAL Audio APM Driver: 1.0. Built Jul 30 2013 11:37:25
JFFS2 notice: (441) check_node_data: wrong data CRC in data node at 0x025ae5c0: read 0x19dc6012, calculated 0x43362103.
HAL Audio PCM Driver: 1.0. Built May 20 2015 14:51:16
channels=1 channel_select=0
BT GPIOs: RST_B=2 VREG_CTL=3 WAKE=4
BT GPIOs: RST_B2=7 VREG_CTL2=6 WAKE=4
HAL Audio USB Core Driver: 1.0. Built Nov  6 2014 16:47:05
usbcore: registered new interface driver HAL Audio USB
HAL Audio USB Driver: 1.0. Built Nov  5 2014 16:02:37
LDX Kernel Driver
@(#)IMAGE_ID:Endpoint Driver (built on Feb  5 2013 19:21:24)
ept:endpoint_init: entry
haltopInit: Booting TL3 processor
VPM Load address=0x30800000 size=624
VPM Load address=0x00010000 size=592632
VPM Load address=0x30a00000 size=65536
VPM Load address=0x000b22b0 size=271968
haltopInit: Booting TL3 processor - Complete
tl3AndLccInit: Initializing IPC for LCC
tl3AndLccInit: Initializing IPC for LCC - Complete
--- Setting up random device ---
512+0 records in
512+0 records out
512 bytes (512B) copied, 0.111946 seconds, 4.5KB/s}

Any help ?

Thank you,
Vasco Santos