Why my Snom M65 doesn't show the transfer Key

Problem

In case you are facing this issue:

1. A (Snom M65) calls B
2. A talks to B
3. A presses transfer 
4. A shows a dial screen - A dials the number of C
5. A does not show the transfer key while typing the C number

Solution

You can solve the issue with a handset reset.

• Page:
  Adding an M5 or M6 repeater in a multicell environment
• Page:
  After upgrading my DECT base to 400B02 my M65 cannot register anymore
• Page:
  After upgrading my DECT multicell system, I can't access the WUI anymore
• Page:
  After upgrading the base to version 400B02 the provisioning via HTTPS/TLS isn't working anymore
• Page:
  Assign a handset to a SIP account on a M300
• Page:
  Attended or blind call transfer of the 2nd call results in merging the 1st and 2nd incoming call
• Page:
  Can I daisy-chain M5 DECT repeaters
• Page:
  Can I install a mixed system with M700 and M900 together
• Page:
  Can I register a 3rd party DECT handset or repeater to a Snom M300,M700,M900 base station
• Page:
  Common faults on M-series DECT base stations: causes and solutions
• Page:
  Configuring multiple SIP Extensions with an M-series DECT handset
• Page:
  DECT - 1. Multicell Deployment Guide
• Page:
  DECT - 2. Physical installation
• Page:
  DECT - 3.0 Multicell setup
• Page:
  DECT - 3.1 Add Extensions
• Page:
  DECT - 4. Site Survey
• Page:
  DECT - 5. Measuring with DECT Discovery Mode
• Page:
  DECT - 6. Best Practises
• Page:
  DECT - Beacons How-To
• Page:
  DECT M-Series How-to
• Page:
  DECT M-Series Provisioning
• Page:
  DECT M100 KLE How-to
• Page:
  DECT M500 How-to
• Page:
  DECT MSC-Series How-to
• Page:
  DECT Solution FAQ
• Page:
  DECT Solution How-to
• Page:
  DECT Troubleshooting How-to
• Page:
  Determining the IP address of your DECT M-SC-Series base
• Page:
  Difference between DECT and configuration synchronization
• Page:
  Do the M300,M700,M900 support GAP
• Page:
  Dropped connections and failed handset handovers in a DECT multi-cell
• Page:
  Dropped SIP registrations on DECT multicell
• Page:
  End of Support for the M700 on 3CX V18
• Page:
  Entering Web Interface - WUI of your Snom DECT-M-SC Series Base
• Page:
  How can I register the A190 headset on an M-Series base station
• Page:
  How can I register,deregister the A150 and the C52-SP on the A230 DECT Dongle
• Page:
  How can I register,deregister the A150 on the A230 DECT Dongle
• Page:
  How can I register,deregister the C52-SP on the A230 DECT Dongle
• Page:
  How can I switch the call between the A190 and an Mxxx handset when paired
• Page:
  How can I trigger a settings sync on a DECT M300,M700,M900
• Page:
  How can I use my Snom phone at home
• Page:
  How do I configure a M300, M700, M900 with the SIP Account from my Provider
• Page:
  How do I pair the A190 headset with an Mxxx series DECT handset
• Page:
  How to assign functions to the A190 buttons
• Page:
  How to auto upgrade firmware on M500, M55, M56, M58
• Page:
  How to check which firmware version is currently installed on M500, M55, M56, M58
• Page:
  How to configure a multi line solution (KeyLine and private line) on a M100 KLE
• Page:
  How to configure KeyLine on a M100 KLE
• Page:
  How to configure RingCentral SIP settings on an M300, M700 and M900
• Page:
  How to configure site-wide vs. local settings in a M500 Pro configuration